Automated Lighting System + DMX

The Automated Lighting System (ALS) is a multi-illuminant (1 tungsten + 3 fluorescent) lighting system that provides uniform lighting between 1 and 1,000 lux over a large space.

An illuminance feedback loop automatically stabilizes light levels, and the entire system is computer-controlled so that you can program your own lighting scenarios, including controlling the color temperature. Lighting control software ensures perfect repeatability of your illumination conditions.​

References:
LIGHTING_SYST
LIGHTING_BULBS
LIGHTING_SETUP

General specifications:​

  • Size: 655x230x1490 mm​
  • Material: Aluminum​
  • Fluorescent tubes and halogen lamps

Technical Specifications:​

  • From 1 to 1,000 lux​
  • Spectrum: 400–950 nm

Key features:​

  • Closed loop
  • Computer control​
  • API software

Dynamic Lighting System​ + DMX

Hand-in-glove with the Automated Lighting System (ALS), this lighting setup takes automation one step further by providing instant lighting intensity changes, thus allowing camera engineers to swiftly perform image quality tests under a multitude of lighting conditions without wasting any time. The DLS is equipped with LED lamps that complement the ALS’s tungsten and fluorescent lighting, and also provides controllable ultra-low-light conditions below 1 lux. You can integrate the Dynamic Lighting system within an automated workflow.

The DLS (Dynamic Lighting System) is composed of two dimmable LED lighting fixtures controlled by PC, providing instant light intensity change between 0.5 lux and 1,300 lux. It is used to reproduce sudden lighting changes to simulate use cases such as switching on the light or going into a tunnel.

The entire system is computer-controlled so that you can program your own lighting scenarios, including controlling the color temperature. The Lighting Control software ensure a perfect repeatability on your illumination condition.​

Reference:
DLS_001

General Specifications:​

  • Size: 142x82x1000 mm​
  • Material: Aluminum​
  • LED

Technical Specifications:​

  • From 0.5 to 1,300 Lux​
  • Color temperature: 2600-2700K
  • Color Rendering Indice: >96

Key features:​

  • Rise time <10ms
  • Computer control​ & API software​
  • Perfect mate of ALS

Multispectral Lighting Systems

Standard Multispectral Lighting System

The Multispectral Lighting System (MLS) is designed to illuminate test charts of up to a width of 2 meters with more than 90% uniformity for image analysis. This new lighting system uses 16 LED channels that can be fully controlled independently and can automatically fit a spectrum with a closed-loop (standard spectra are pre-calibrated). The LED channels are DC-driven, ensuring flicker-free light, although LED flicker can be activated. This lighting system can reach very low light (down to 0.1 lux with 10% precision).

An illuminance feedback loop automatically stabilizes light levels, and the entire system is computer-controlled so that you can program your own lighting scenarios, including the color temperature. The software ensures perfect repeatability of your illumination conditions.​

Sunlight-Near Infrared Multispectral Lighting System

This lighting system has the same characteristics as the standard MLS product, but comes with 4 additional LED channels in near-infrared (NIR) and one additional LED channel in visible light. This creates an unprecedented ability to mimic daylight by reaching light levels up to 50K lux with a spectrum that goes through the full range of visible light and NIR.​

General specifications:​

  • Size: 785 x 203 x 1590 mm​
  • Material: Aluminum​
  • Weight: 45 kg

Technical specifications:​

  • From 0.1 to 50 000 lux​
  • Spectrum: 360–980 nm
  • Flicker mode: 50–1000 Hz (50% duty cycle)
  • Ethernet connection
  • 100-240V 50-60Hz
  • max consumption : 2500W

Key features:​

  • Flicker-free (DC-driven)
  • Closed loop (light level and spectrum)
  • Computer control​ & API software​
  • Flicker mode (independent for each side)​
  • Short raise time (<30 ms)
  • Daylight (0.1 to 50K lux), IR (700 to 980 nm)
  • Reference: MLS_001 & MLS_SUNIR_001

LED panel Kinoflo + DMX

This LED panel can be used for test chart illumination such as our Composite chart or Natural scene chart, it can also be used as lightning system.

The entire system is computer-controlled so that you can program your own lighting scenarios, including controlling the color temperature. The Lighting Control software ensure a perfect repeatability on your illumination condition.​

General Specifications:​

  • Size: 610x355x127mm
  • Material: Aluminum
  • Reference: KINO_CELEB_250
  • Computer control​ & API software​

Technical Specifications:​

  • Spectrum type: LED
  • Color temperature: 2500K to 9900K
  • Dimming PWM 250Hz 100% to 0.2%

Spectralight​ QC

The Spectralight QC Setup is our most compact and cost-effective lighting setup solution, ideal for small labs with limited budget. Its metal frame makes it stable, durable, and safe. Its light weight allows for easy movement and fixation. Its light sources are temperature-adjustable and fully dimmable for a wide range of testing conditions.

Reference:
XRITE_SPECTRA

General Specifications:​

  • Size: 700x1000x1850 mm​
  • Material: Aluminum alloy​
  • Surface treatment: Black oxide

Technical Specifications:​

  • Light source: D50 or D65, two TL84/U30/U35, CWF, UVA, 2300K, CIE A*​
  • Color temperature: 2500-9900K
  • Temperature: 0-35°C

Key features:​

  • Temperature-adjustable​​
  • Fully dimmed​
  • Adjustable pink and green parameters, hue, saturation and RGB values